How to Fix Samsung Washing Machine Se Error Code?
by Ushapriyanga
Updated Apr 19, 2023
What is Samsung Washing Machine Se Error Code?
The SE error code on a Samsung washer suggests a drainage problem, which may be denoted by a 5E or nd code on certain models. It is important not to confuse this with the E5 code, which indicates a heating element problem. If you encounter the SE error code, refrain from opening the front door of a front-loading washer as it could result in spilled water.
While temporarily disconnecting power for a minute or two may help, it is necessary to address the underlying issue as ignoring the error could result in more severe problems in the future. Exercise caution while disconnecting hoses from the washer, as there could be a significant amount of water in them, which may suddenly spill out.
It is advisable to manually empty the washer's tub before proceeding with the disconnection of any hoses. When attempting to troubleshoot the SC error code, ensure that you have a sizable container to collect the water.
How to Fix Samsung Washing Machine Se Error Code?
Clean the Pump Filter (Front-Loader Washers)
If you own a Samsung front-loader washer, it may have a pump filter that needs to be cleaned at least once a month or after 40 laundry loads. This is important to prevent unpleasant odors, mold, and mildew, and to ensure that your washer drains correctly. Here are the steps to clean the pump filter:
- Open the pump filter access panel and locate the black rubber drain hose.
- Remove the white drain plug from the hose and drain the water into a large container. Be prepared for some water to spill.
- Depending on your washer model, either remove the pump filter by turning it counterclockwise and pulling it out or by pushing it in and turning it like a medicine bottle.
- Clean the filter with soap and water, using a small toothbrush or soft bristle brush to help clean dirt and debris off.
- Return the filter to the washer, replace the hose plug, and return the hose to its mounting clip.
- Close the access panel.
Check the Drain Hose
If your washer is not draining properly, it may be due to a kinked, pinched, or obstructed drain hose, or a submersed drain hose outlet. Here are the steps to check and fix your drain hose:
- Check the drain hose is connected properly and there are no bends or kinks.
- If the washer's drain hose is connected to a standpipe, make sure it is positioned and secured properly, and check that it is at least 23 inches above the floor.
- Make sure the standpipe covers the drain hose completely, and there are no more than 6 inches of drain hose in the standpipe.
- Unblock the drain hose with a drain snake tool, or wash the hose with a mixture of hot water, white vinegar, and baking soda.
- To check the internal drain hose, follow the drain pump cleaning instructions below.
Defective Drain Pump
If the drain hose is not blocked, a defective drain pump may be the cause of the issue. Here are the steps to check your drain pump:
- Disconnect the washer from the power source and water supply.
- For the front-loader washer, remove the rear access panel. For the top-load washer, secure the lid with tape and lay the washer on its front.
- Disconnect the drain pump wire connector and check the wiring harness on the drain pump. Make sure it is secure with no visible damage to the wiring.
- Use pliers to release the clamps that secure the drain hose to the pump. Remove the drain hose.
- Use a 5/16-inch socket to remove the drain pump mounting screws and remove the pump from the washer.
- Check the pump for damage or obstructions.
- If the pump does not have any damaged components and is free of obstructions, check the drain pump motor using a multimeter to determine if it has continuity. If the motor tests negative for continuity, the pump needs to be replaced.
Causes for Samsung Washing Machine Se Error Code
When the SE error code appears on your washer, it means that the draining cycle is taking too long. The length of time the draining cycle should take is determined by the load size and cycle type. Typically, the SE error code is caused by a faulty drain pump, clogged drainage system, or filter.
If you have already checked the filter, drain hose, and drain pump and the error code persists, the problem may be with the pressure switch. This component informs the control board when to add or drain water. If the signals the control board receives are incorrect, it may not drain properly. The pressure switch can be tested with a multimeter, and if defective, it can be replaced inexpensively.
In case the error code continues to appear, the control panel or timer may be causing the issue. These parts can be challenging to test with a multimeter and often need to be replaced. It is recommended to seek assistance from a trained professional.
What is Samsung Washing Machine?
Samsung Washing Machine is a household appliance designed and manufactured by Samsung Electronics, a South Korean multinational electronics company. It is a machine that is used for washing clothes and other fabrics. Samsung offers a variety of washing machine models, including top-load, front-load, and washer-dryer combo machines, with different features and specifications to suit different customer needs.
Samsung washing machines come with various innovative features such as eco-bubble technology, which mixes air, water, and detergent to create bubbles that penetrate the fabric quickly and remove dirt easily, and AddWash, which allows you to add forgotten clothes or items during a wash cycle. Samsung washing machines also have a digital display that shows the time remaining for the wash cycle to finish, the chosen wash program, and other relevant information.
How to Fix Samsung Washing Machine Se Error Code - FAQs
The SE error code indicates that the washer is not draining quickly enough
The usual causes of the SE error code are a faulty drain pump, a clog in the drainage system, or a clogged filter.
First, check the filter, drain hose, and drain pump for any clogs or obstructions. If that doesn't fix the issue, check the pressure switch to see if it needs to be replaced.
It depends on the complexity of the issue and your technical expertise